Amp power - Hyundai Elantra GT Turbo & Elantra GT N Performance Forum
 
LinkBack Thread Tools
post #1 of 7 (permalink) Old 07-15-2019, 04:55 PM Thread Starter
Junior Member
 
Join Date: Jul 2019
Posts: 19
Amp power

Where is the best place for amp power to enter the body? I have 4awg.
Tvalenti is offline  
post #2 of 7 (permalink) Old 07-15-2019, 10:53 PM Thread Starter
Junior Member
 
Join Date: Jul 2019
Posts: 19
Well I figured it out finally hooked everything up to the factory radio. I followed the color code for the rear speakers from the Crutchfield pdf. Turned all gains down and can’t get it to sound right. Used an LC2i alpine mv500 and 8” enclosure R type. Had it in a different car prior but with an alpine headunit. Makes the sub sound like it’s blown. Any ideas?
Tvalenti is offline  
post #3 of 7 (permalink) Old 07-16-2019, 07:50 AM
Member
 
Join Date: Feb 2019
Posts: 39
Try hooking up a different source such as your phone and see if it still sounds blown. Try reversing polarity of wires going to subwoofer.
jetrep is offline  
post #4 of 7 (permalink) Old 07-16-2019, 09:06 AM Thread Starter
Junior Member
 
Join Date: Jul 2019
Posts: 19
Tried polarity last night and it is the same. Did not try a different source yet. Kinda sounds like too much power going to it like clipping. Doesn’t sound like the LC2i is doing what it’s supposed to. I used the yellow/black and brown/white wires from the back of the factory radio.
Tvalenti is offline  
post #5 of 7 (permalink) Old 07-17-2019, 11:26 AM Thread Starter
Junior Member
 
Join Date: Jul 2019
Posts: 19
Replaced sub. Good to go. Was blown.
Tvalenti is offline  
post #6 of 7 (permalink) Old 07-17-2019, 02:03 PM
Junior Member
 
Join Date: Jun 2019
Posts: 15
If you could post photos of the wires you tapped into and how they connected to your amp, or links of info, that would be helpful. I’m interested in adding an amp/sub but not sure I want to commit yet..
niccuany is online now  
post #7 of 7 (permalink) Old 07-17-2019, 04:10 PM Thread Starter
Junior Member
 
Join Date: Jul 2019
Posts: 19
Everything is behind the dash. I got the Crutchfield instructions from another post. Used yellow/black and brown/white behind the deck. This is a base model. I do not have the factory sub and amp. I used 16-18g Posi taps.

Tapped those for audio and I used the red white from the grey connector for power. Should be an orange and red next to each other. I used the black from the same connect for ground. Stick the LC2i behind the dash above the glove box. Ran the rca and remote wire to the back on pass side.

Knowing what I know now tho I would’ve ran the rca/remote wire on the left side. The easiest grommet to use is on pass side for power from battery. Push the power through the firewall from the engine bay. Make sure you use your finger first to push inside the grommet and make sure you’re in the correct hole. It’s not the small hole on the outside of the grommet. It’s like a double walled grommet. Unravel some tape on the harness and grommet then make sure you’re inside the harness.

Use a philips screwdriver with wd40 and push it in easily and try to stay against the harness. If not you will poke a hole through the grommet on the inside. You don’t want to do that you want to expand the grommet around the harness you won’t need a lot of force to get on the other side. Once you feel it push through send the power wire in with the screwdriver still in there to help keep the grommet open and slide the power lead in.

You will need to push enough wire inside the cabin to find it. It’s behind the cabin filter so you will need to unclip the bottom panel with 3 clips and pull it out under the glove box. Keep using wd40 on the wire to slide it through the grommet easily. Don’t tug on it without it. You’ll invert the grommet and make it not seal or worse tear it. Stick the wd40 hose inside the grommet to not make a mess and it’ll lube the wire.

Once this is all done just pull the sill plate trim out towards the seats and start tucking the wires under and make your way to the trunk.

Tools required are Phillips and plastic panel tools. It helps not damaging the dash.

Find the Crutchfield instructions for removing all the panels. It’s linked on this forum. It helped me with removing all the panels and wires. I ohm tested the wires too before splicing. They should 4.5ohms if they are speakers.
Tvalenti is offline  
Reply

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome